How To Start A Jeep Cherokee Without A Key?

Jeeps are a popular car for outdoor enthusiasts and off-road adventurers. Many people choose to buy them because of their high ground clearance and four-wheel drive.

But if you’re one of the many people who don’t have a key to start your Jeep Cherokee, don’t worry – there are several ways to start it without one.

In this blog post, we’ll walk you through three different methods for starting your Jeep without a key.

What You’ll Need to Start a Jeep Cherokee without A Key?

If you’re like most Jeep Cherokee owners, you probably don’t think about how you would start your Jeep if you lost your keys. After all, why would you need to? Your Jeep has a keyless entry system that allows you to start it without using a key.

What You'll Need to Start a Jeep Cherokee without A Key

However, there are times when this system can fail and you may find yourself in a situation where you need to start your Jeep without a key.

Fortunately, there are a few ways that you can do this. One way is to use a screwdriver to manually turn the ignition. Another way is to use a spare key if you have one. And finally, you can also use a battery jump starter to start your Jeep.

Let’s take a look at each of these methods in more detail.

Starting Your Jeep With A Screwdriver

If you find yourself in a situation where you don’t have a key and you need to start your Jeep, one way to do it is to use a screwdriver. This method is not for the faint of heart, but it is possible.

First, you’ll need to remove the plastic cover that is located around the ignition switch. Once you have this cover off, you’ll need to locate the small pin that is holding the ignition switch in place. Using a screwdriver, carefully pry this pinout.

Once the pin is out, you’ll be able to turn the ignition switch with the screwdriver. Be careful not to break the ignition switch, as this can cause serious damage to your Jeep.

Starting Your Jeep With A Spare Key

If you have a spare key, you can use this to start your Jeep without a key. This method is much easier than the screwdriver method, but it does require that you have a spare key.

To start your Jeep with a spare key, simply insert the key into the ignition and turn it to the “on” position. Your Jeep should start without any problems.

Starting Your Jeep With A Battery Jump Starter

If you don’t have a key and you don’t have a spare, you can still start your Jeep with a battery jump starter. This method is a bit more complicated than the other two, but it is still possible.

To start your Jeep with a battery jump starter, you’ll need to locate the positive and negative terminals on your Jeep’s battery. Once you have these located, you’ll need to attach the positive terminal of the jump starter to the positive terminal on the battery.

Then, you’ll need to attach the negative terminal of the jump starter to the negative terminal on the battery. Once you have the jump starter connected, you’ll need to turn it on. This will provide power to your Jeep’s battery and allow you to start the engine.

Keep in mind that you’ll need to keep the jump starter connected to your Jeep’s battery for a few minutes after the engine is started. This will help charge the battery and prevent it from dying.

If you find yourself in a situation where you need to start your Jeep without a key, there are a few different methods that you can use. You can use a screwdriver to manually turn the ignition, you can use a spare key, or you can use a battery jump starter.

Where to Find the Starter Relay to Start a Jeep Cherokee without A Key

If your Jeep Cherokee has been sitting for a while, or if the battery has been disconnected, you may need to find the starter relay in order to start the engine. The starter relay is located in the engine compartment, on the driver’s side near the battery. It is a black box with a white label that says “starter relay.”

If you cannot find the starter relay, consult your Jeep Cherokee’s owner’s manual. Once you have found the starter relay, use a screwdriver to remove the cover. Inside the box, you will see two large terminals and two small terminals. The large terminal on the left is for the battery cable, and the large terminal on the right is for the starter cable.

The small terminal on the left is for the ignition switch, and the small terminal on the right is for the starter solenoid. To start the engine, connect the battery cable to the large terminal on the left, and then connect the starter cable to the large terminal on the right.

Finally, connect the ignition switch to the small terminal on the left, and then connect the starter solenoid to the small terminal on the right. Once everything is connected, turn the key to the “on” position, and then press the start button.

The engine should start immediately. If it does not, check all of your connections and make sure that the battery is fully charged.

How to Start Your Jeep Cherokee without A Key?

If you’re like most Jeep Cherokee owners, you probably don’t give much thought to how you start your SUV. After all, as long as the key is in your pocket and the engine starts, what’s the big deal?

How To Start A Jeep Cherokee Without A Key

But what if you lost your keys or they were stolen? How would you start your Jeep then? Fortunately, there’s a way to start your Jeep Cherokee without a key. All you need is a wire coat hanger and a few minutes of time.

Here’s how to do it:

  • Insert the end of the coat hanger into the keyhole on the driver’s side door.
  • Push the coat hanger down until you feel it touch the bottom of the keyhole.
  • Turn the coat hanger so that the hook end is facing up.
  • Insert the hook end into the keyhole and turn it clockwise.
  • Continue turning the coat hanger until you hear the click of the door unlocking.
  • Now, insert the coat hanger into the keyhole on the ignition.
  • Push down on the coat hanger until you feel it touch the bottom of the keyhole.
  • Turn the coat hanger so that the hook end is facing up.
  • Insert the hook end into the keyhole and turn it clockwise.
  • Continue turning the coat hanger until you hear the click of the ignition unlocking.
  • Now, you can start your Jeep Cherokee without a key!

If you don’t have a wire coat hanger handy, you can also use a paperclip or a straightened-out paperclip. Just follow the same steps as above.

So there you have it starting your Jeep Cherokee without a key is easy and only takes a few minutes.

So if you ever find yourself in a situation where you’ve lost or misplaced your keys, don’t panic. Just grab a coat hanger (or paperclip) and you’ll be on your way in no time.

The Consequences of Starting Jeep Cherokee without A Key

Starting a jeep Cherokee without a key can be costly and time-consuming. Without the key, the engine will not start, making it difficult to get to your destination. In addition, the keyless entry system will not work, meaning you’ll have to manually unlock the doors.

The cost of a replacement key can range from $100-$500, depending on the make and model of your Jeep. If you’re stranded somewhere, you may also have to pay for a tow truck or other assistance.

So, it’s important to always have your key with you and to make sure it works before you get in the car.

Tips and Tricks for Keeping Your Jeep Cherokee Running Smoothly

  1. Check your fluids regularly
  2. Keep an eye on your tires
  3. Get regular tune-ups
  4. Take care of any rust spots immediately
  5. Store your Jeep properly during the winter months
  6. Do not allow anyone to smoke inside your Jeep
  7. Clean your Jeep regularly
  8. Keep your Jeep’s interior free of clutter
  9. Take your Jeep to a professional for any major repairs
  10.  Enjoy your Jeep!

Last Thought

Jeep Cherokee owners have several options for starting their vehicle. You are now able to start your Jeep Cherokee without a key. We hope that this article was helpful and informative. If you have any questions or concerns, please do not hesitate to reach out to us. Have a great day!

Miguel Watts

Miguel is an automobile engineer, who works in his automobile workshop. He is in this track for almost fifteen years, so he has vast experience with automobile tools and accessories. Besides this profession, he’s a hobbyist blogger who loves to research different tools and accessories of cars, motorbikes, automobiles, etc., and shares his findings with others. The Toolsinsider is a result of that. Miguel creates this site to share his findings with a broader audience.

Leave a Reply

Your email address will not be published.

Recent Posts